How to safely check the brake fluid level and condition

刹车让你活下去。 这并不夸张。 但是,了解如何检查制动液 是大多数驾驶员都会忽视的一项技能,直到踩踏板感觉就像踩进了一袋棉花糖。

这并不难。 如果你注意的话,并不危险。 这就是例行维护停车和拖车之旅之间的区别。

以下是如何检查您的储液罐、发现污染并知道何时停止猜测并开始修复。

找到制动总泵储罐

打开引擎盖。 寻找制动助力器——防火墙(将发动机与驾驶室隔开的墙壁)上的一个大的、深色的圆形部件。 储液器位于与之相连的主缸的正上方。

在现代汽车中,它是一个半透明的塑料容器。 您会看到侧面刻有最小/最大线。 如果您驾驶经典或较旧的欧洲车型,您可能会发现带有旋盖的金属罐。

还不确定吗? 检查用户手册。 它有一个图表。 如果找不到,请寻找带有刹车符号(周围带有括号的圆圈)的盖子。

找到后,先不要打开它。 只要透过塑料看一下。

液体是否低于最低线? 这是你的第一个危险信号。 低液位通常意味着两件事:刹车片磨损或泄漏。 该系统通过将更多流体推入卡钳、降低储液罐液位来补偿制动片磨损。 随着时间的推移,它会略有下降,这是正常的。 如果是空的? 有问题。

检查制动液状况

数量很重要。 清晰度更重要。

新鲜的制动液是清澈的。 它看起来像浅琥珀色或淡黄色。 一些合成混合物可能带有轻微的绿色或粉红色调,但它应该是透明的。

如果它是深棕色、浑浊的,或者看起来像淡茶,那么它就被污染了。

为什么这很重要? 制动液具有吸湿性。 它通过橡胶软管和密封件中的微小渗透吸收空气中的水分。 水的蒸发速度与乙二醇基液体的蒸发速度不同。 更多的水意味着更低的沸点。

热刹车会使液体沸腾。 沸腾的液体变成气体。 气体压缩。 液体则不然。 制动管路中的可压缩液体意味着您的脚会踩到地板,而汽车不会停下来。

您可以在任何汽车配件商店购买测试条或电子测试仪。 他们测量水分含量。 如果超过3%,请冲洗。 不要等到沸腾。

添加制动液(如有必要)

If the level is low, but the fluid looks clean, you can refill it. But there’s more to it than just picking up a bottle.

Brake fluid is classified according to DOT (Department of Transportation) standards. The most common are DOT 3, DOT 4 and DOT 5.1.

DOT 3 and DOT 4 are glycol-based. They are generally compatible with each other, but DOT 4 has a higher boiling point. DOT 5 is silicone based. Not miscible with ethylene glycol. When DOT 5 is placed in a glycol system, a gel forms. The brakes no longer work.

Check the user manual. Use the specified type. If in doubt, use DOT 3 or DOT 4. However, do not mix the types.

Wipe the area clean before removing the cover. When dirt builds up inside the master cylinder, it can be a nightmare to fix. Pour slowly. Stop at the maximum line. Overfilling can cause fluid to splash (spill) onto hot engine parts. Close the lid tightly.

Know when to replace or inspect

Low fluid content is not always a problem. This is a symptom.

If you refill it and the levels drop again after a week, you have a leak. Check for puddles under your car. Check the wheel wells for moisture. Check brake calipers and brake hoses. As the seals age, the brake caliper and wheel cylinder often leak.

If the brake pedal feels spongy, there may be air in the system. This can happen after a leak, a pad change, or a master cylinder seal failure. There is air in the pipe, so it must be removed. This is not a DIY job unless you have someone to help you and know what you are doing.

Don’t miss the soft pedals either. This was a warning shot.

What if the liquid looks like chocolate milk? It is a mixture of coolant and brake fluid. This usually means that the master cylinder diaphragm is faulty. The vacuum pipe of the brake booster sucks coolant into the tank. This is a major failure. Stop driving. 拖走它。

Checking the brake fluid takes 30 seconds. There are no expenses. It might save your life. Do the same the next time you check the engine oil. Or tire pressure. 或者只是因为你关心不要撞车。